Settling problem on RAM (Random Acess Memory)

Newbie : Why are Windows detect fewer RAM from truthfully?
Arief : There are many causative thing, amongst those is:

1. "Damage" physical". To settle it You shall check that RAM physical condition. casing's open Your computer, then pulls out that RAM. Clear if RAM and is mess. Check also what there is karat. You shall also ensure that TAM from material same (golden or silver). If different, better You substitute that RAM.
2. ROM Shadowing In Many BIOS and driver 16 bits, sometimes uses partly (read: little bit) Louvre before Windows 2000 is carried on. Severally BIOS also available feature ROM shadowing what do will fill from system and BIOS ROM'S video goes to RAM utilisedding to increase performa computer (On PACK and Windows 2000 3.1). It because speed ROM inferior from RAM. But if You use Windows 95 / 98 / NT with memory that feature ROM shadowing's advisable minim is switched off only (from CMOS Setup), since Windows 95 / 98 / NT scarcely over accesses ROM so that RAM gets to be utilized by Windows.
3. VGA Card On Board's purpose. If e.g. You have RAM 32 Mb and VGA Card 2 Mb, therefore applicable RAM just as big as 30 Mb (32 Mb 2 Mb). So advisable doesn't use VGA Card On Board.
4. Available driver or program that is carried on from config.sys or autoexec.bat what do work to utilize RAM. Its solution: Edit autoexec.bat's file and config.sys by use of Notepad. Then edits on row that "suspect" or one approximately being utilized for me load programs. If ketemu adds to say BRAKE (but if You add to say BRAKE therefore that program won't at load / is carried on). If You use driver ROM'S CD 4x from Teac, change xmssize='s parameter 1 on autoexec.bat becomes xmssize=0.
5. Virtual device driver is carried on from system.ini. To settle it this system's open by clicks To Start Run type. Vote for system.ini. Then edits on row that approximately been utilized for meload virtual device driver. Another alternative is with make system.ini's file a new one.
6. Available row Maxphyspage on system.this file Pleases to see on system. this file, what exists Maxphyspage's row or not. If yes, that row delete.
7. Fault on CMOS Setting. In many computer exists feature Memory Hole at 16 Mb or Hold To 15 Mb LOUVRES. If feature that at enable therefore if You have greater RAM from 15 Mb or 16 Mb, Windows will remain detect as big as 15 Mb or 16 Mb. To settle it, please at disable feature that.
8. Meload Ramdrive.sys from config.sys Check your Config.sys for a's file containing's line "Ramdrive. sys." If you have this is line, it means you is using's acre a. drive's RAM. To disable the is drive's RAM, remove or disable the is in the Config.sys's line that contains's file "ramdrive. sys." To disable the is line, use a. text editor (such is Notepad's usa) to edits the Config.sys and place's file a. semicolon(;) at the beginning of the is line. config.sys's file open with Notepad. Cheque on that file, what exists ramdrive.sys's row. If yes, that row delete.

Newbie : Why happens error my afters install new RAM?
Arief : You can see on booknya's manual.
For a few BIOS: If You menginstall (e.g.) 2 - 4 Mb SIMMS and 2 8 Mb SIMMS, You shall place greater RAM on Bank 1.

Newbie : After adds RAM, why what do RAM be detected still with?
Arief : After You menginstall RAM, You get to do setup BIOS re. Its trick, on first time starts up computer until BIOS'S logo appearance, Del's press (for a few computer That Ctrl may + Alt + Del or combine to y. the other). After is finished, vote for Save Setting And Exit. In addition information for setting that, You can read on manual book.